Sofa Door Fit Calculator
Enter the sofa's size and the door opening to see whether it goes through upright, on its back or rolled, and how much room is left.
The calculator failed to load. Please reload the page.
Measure the narrowest point
Measure the opening from stop to stop and from the floor or threshold to the underside of the head, not the door slab. Handles, hinges and trim along the route can be narrower still.
Measure the sofa at its widest points, including arms, back and legs. A tape across the sofa's end, from the floor to the top of the back, gives the size that has to clear the frame.
The first example at the doorway
Sofas and doors
- An 84 x 36 x 34 in sofa and a 36 x 80 in opening: After the spare gap, the usable opening is 35 in x 79 in. Upright it is too deep, but on its back it goes through with 1 in to spare: its 34 in height becomes the width.
- A shallower sofa, 30 in deep: It now goes through upright, with 5 in to spare.
- The same door left on its hinges: A door 1 3/4 in thick, opened fully, leaves 34 1/4 in, and 33 1/4 in after the spare gap. The first sofa does not fit; lifting the door off is what makes it work.
- A 32 in door: Usable width is 31 in, less than the sofa's smallest side of 34 in, so as a box it does not fit. A sofa is not a box, though: if its diagonal depth is 29 in, it goes through tilted back (diagonal depth) with 2 in to spare.
- A hallway turn right after the door: With a 60 in hall, a sofa carried flat must be no longer than 59 1/8 in to turn the corner; this one is 84 in. Stood on its end, its 36 in x 34 in footprint turns easily, but tipping it up swings its top corner through 91 5/8 in (the diagonal of its length and its 34 in footprint side, plus the spare room), so the ceiling must be at least that. Under a 96 in ceiling the result is: fits if stood on end at the corner.
Longest piece that turns a hallway corner flat
Through a 36 in doorway into a hall at a right angle, how long can a sofa, mattress or cabinet be and still turn the corner lying flat? Find the hall width on the left and the width of the piece across the top.
| Hall width | Piece 24 in across | Piece 30 in across | Piece 34 in across |
|---|---|---|---|
| 36 in | 50 in | 38 in | 30 in |
| 40 in | 56 in | 44 in | 36 in |
| 44 in | 61 in | 49 in | 41 in |
| 48 in | 67 in | 54 in | 45 in |
| 54 in | 74 in | 61 in | 52 in |
| 60 in | 81 in | 68 in | 59 in |
Longer than the figure, it may still go round stood on its end; the calculator checks that with your ceiling height.
Computed for this page with the corner check the calculator uses; no published table was used. Each cell is the shortest clearance over every turning angle for a rectangle of the given width moving between two straight passages, leaving 1 in of room in each passage, rounded down to a whole inch. It is the same calculation as the hallway check above.
Usable width of common door sizes
Keeping 1 in spare; a door left on its hinges, opened fully, takes about 1 3/4 in of the width. Skip to the calculator
| Door width | Door taken off | Door left on, fully open |
|---|---|---|
| 30 in | 29 in | 27 1/4 in |
| 32 in | 31 in | 29 1/4 in |
| 34 in | 33 in | 31 1/4 in |
| 36 in | 35 in | 33 1/4 in |
Measure your own opening at its narrowest point and use the calculator for your sofa.
What it cannot see
- Geometry only. It cannot see steps, low ceilings, light fittings, banisters, door handles or the strength of the piece. Moving is at your own risk.
- It does not model removable legs, arms and backs, cushions that squash or frames that flex. If you will take the legs off, enter the size without them.
- The piece is pushed straight and rolled. Pivoting it through a thin wall can sometimes gain a little, so a near miss can be worth a careful trial; a narrow pass should be checked with a tape.
- Stairs and lifts are not covered. The hallway check is one right-angle turn between two straight passages.
How the fit is checked
The sofa is first treated as a rigid box. For each way it can go through, upright, on its back or on its end, and rolled at every angle in between, the width and height its end takes up are compared with the usable opening; a pass needs both to fit after the spare gap you set. If you give the diagonal depth (the furniture-store measurement of the sofa's slanted side profile), it also tries the sofa tilted back, length first, where only that diagonal has to clear the width. If you give a hallway width, a right-angle turn is checked; when the flat turn fails, it checks whether the sofa stood on its end would turn the corner, and needs a ceiling height to confirm that.
Defaults you can change, and why they are set this way:
- 1 in (25 mm) spare gap: Hands, padding and an uneven floor need some room; you can change it to zero
- door 1 3/4 in (45 mm) thick: Exterior doors in the US are commonly 1 3/4 in thick and interior doors thinner; you can change it
Sources:
- ICC 2021 International Residential Code, R311.2 Egress door (clear width and height) (checked 2026-11-14)
Doorways it was tested on
Geometry is easy to get subtly wrong, so 12 doorway and hallway cases were written out step by step, separately from the calculator code, and the calculator has to agree with every one before this page is built. None of them comes from an outside source.
| Sofa and opening | Verdict it must reach | Why |
|---|---|---|
| Sofa 84 x 36 x 34 in; door 36 x 80 in, taken off; 1 in of clearance wanted | Fits if turned, 1 in to spare | The free opening is 36 - 1, so 35 in wide. Upright, the sofa's end is 36 in deep, too wide; on its back the end is 34 in wide, which leaves 1 in. |
| Sofa 84 x 36 x 34 in; door 36 x 80 in, left on its hinges; 1 in of clearance wanted | Does not fit | The open door takes 1.75 in, leaving 34.25 in, and 33.25 in after the spare inch. The sofa's smallest side is 34 in, so it does not pass. |
| Sofa 84 x 36 x 34 in; door 36 x 80 in, taken off; 1 in of clearance wanted; 60 in hall, 90 in ceiling | Door OK, hallway turn blocks it | Flat, the 84 in sofa is too long for the corner. Tipping it onto its end swings its top corner through the diagonal of 84 and 34 in, 90.62 in; with the spare inch that is 91.62 in, more than a 90 in ceiling. |
Doorway questions
What is the usual width of an entry door?
US model codes require at least one exit door with a clear opening of at least 32 in wide and 78 in high, measured with the door open. Many front doors are wider, but measure yours: trim, stops and handles take space.
Is it worth lifting the door off its hinges?
Yes: a door left on its hinges stands in the opening when fully open and takes about its own thickness from the width. In the worked examples, a 36 x 80 in opening is enough with the door off and not with it on.