Measured Maker

Tape Measure Fractions Calculator

Add inch fractions exactly, find the nearest tape mark for a decimal or a metric length, and check whether your cuts fit on one board.

Choose a calculation
Build a length with buttons

You can also type lines directly, such as 7 3/8, 1' 2 1/4", 0.4375 or 75 mm.

Lengths (one per line)

Where a decimal lands between the marks

Tape measure: where 2.65 in fallsA one-inch section of an inch tape from 2 to 3 inches with sixteenth-inch ticks. An arrow marks 2.65 inches; the nearest mark, 2 5/8 in, is highlighted.232 5/8 in2.65 inEach short tick is 1/16 in. 2.65 in sitsbetween marks; the nearest one is 2 5/8 in.
The arrow is the exact value; the red mark is the one to cut to.

Four lengths worked out

  • 7 3/8 in + 9 11/16 in, minus 1 1/4 in: In sixteenths that is 118 + 155 - 20 = 253/16, so the total is 15 13/16 in (15.8125 in, 401.6 mm), or 1 ft 3 13/16 in.
  • Four pieces of 18 5/8 in: 4 x 18 5/8 in = 74 1/2 in (6 ft 2 1/2 in). Typing 4 @ 18 5/8 saves entering the same length again and again.
  • Where is 2.65 in on the tape?: 2.65 x 16 = 42.4 sixteenths, which rounds to 42, so the nearest sixteenth mark is 2 5/8 in, which is 0.025 in short. 75 mm is 2.9528 in, the 2 15/16 in mark.
  • Two 36 in and two 11 3/4 in pieces from an 8 ft board, 1/8 in blade: The pieces add up to 95 1/2 in and the cuts between them remove 3/8 in, so the board needs 95 7/8 in: it fits, with 1/8 in left over. That is too little to square a rough factory end, so check the ends first.

Before you cut from one board

Every saw cut turns a blade's width of wood into dust, so pieces that add up to the board length do not fit once the cuts are counted. Measure your blade's cut on scrap and enter it.

Factory ends are often a little out of square or dinged. When the cut list shows less than half an inch to spare, plan for a trim cut at the end, or buy one more board.

Sixteenths chart for the workbench

Every 1/16 in mark between zero and one inch, with its decimal value and its length in millimetres. Print it and keep it by the saw, or read a decimal from a plan straight across to the mark.

MarkDecimal inchMillimetresAlso an eighth mark
1/16 in0.06251.6 mmno
1/8 in0.1253.2 mmyes
3/16 in0.18754.8 mmno
1/4 in0.256.4 mmyes
5/16 in0.31257.9 mmno
3/8 in0.3759.5 mmyes
7/16 in0.437511.1 mmno
1/2 in0.512.7 mmyes
9/16 in0.562514.3 mmno
5/8 in0.62515.9 mmyes
11/16 in0.687517.5 mmno
3/4 in0.7519.1 mmyes
13/16 in0.812520.6 mmno
7/8 in0.87522.2 mmyes
15/16 in0.937523.8 mmno
1 in125.4 mmyes

Millimetres are rounded to a tenth; the decimal values are exact.

Computed for this page; any ruler marked in sixteenths and millimetres will confirm it. Each row is a sixteenth of an inch converted by the same code the calculator uses: decimal = sixteenths / 16, millimetres = inches x 25.4, rounded to a tenth.

How the marks are worked out

Fractions you type are kept as whole sixty-fourths of an inch, so adding and subtracting them is exact. A decimal or millimetre length keeps its exact value until the end and is then rounded once to the nearest mark at the step you choose; a value exactly halfway goes up. The cut list adds each piece and one blade width between neighbours, and starts a new board when the next piece would not fit.

Sources:

What it cannot know

  • The result is only as good as the reading: a loose hook or reading the tape from the wrong side matters more than any rounding here.
  • Lumber is sold by nominal size: a board sold as eight feet can be a little longer, and a one-by-four is not one inch by four inches. Type the length you measured.
  • The cut list covers straight cross cuts on one stock length. Mitres, grain direction, knots and defects are up to you.

Arithmetic on record

The fraction arithmetic on this page is pinned by 7 cases written out step by step, separately from the calculator code; 1 of them rests on the legal definition of the inch. The page is not built unless all of them come out right.

You typeIt must answerThe working
Add 1/2 in and 1/4 in3/4 in, 0.75 in as a decimal, 19.1 mm8/16 + 4/16 is 12/16, which is 3/4 in or 0.75 in. 0.75 x 25.4 is 19.05 mm, shown as 19.1 mm.
2.65 to the nearest 1/16 in mark2 5/8 in, 2.65 in as a decimal2.65 x 16 is 42.4 sixteenths, nearest whole 42, and 42/16 is 2 5/8 in. The next mark up, 2 11/16 in, is further away.
4 pieces of 24 in from 8 ft boards with a 1/8 in blade2 boards4 x 24 is 96 in, and the three cuts between the pieces take 3 x 1/8 in, 3/8 in more: 96 3/8 in does not fit a 96 in board, so two boards.
Add 3 1/2 in and 4 @ 2 1/4 in12 1/2 in, 12.5 in as a decimal, 317.5 mm, the list shows + 3 1/2 as 3 1/2 in and + 4 @ 2 1/4 as 9 inFour pieces of 2 1/4 in make 9 in. Added to 3 1/2 in that is 12 1/2 in, or 12.5 in, which is 317.5 mm. The list shows the line once, as 4 @ 2 1/4, with the 9 in it adds.

Reading a tape

Why round the total instead of each measurement?

Each rounding can move a value by up to half a mark, and the errors add up. Three pieces of 5.3 in rounded one at a time give 15 15/16 in; their exact total, 15.9 in, is closest to the 15 7/8 in mark. Add exact values and round once.

How do I read 0.4 in on an inch tape?

Multiply by sixteen: 0.4 x 16 = 6.4 sixteenths, so the nearest mark is 6/16, which is 3/8 in, 0.025 in short of the value.

What is 250 mm in inches and fractions?

250 / 25.4 = 9.8425 in. In sixteenths that is 157.48, so the nearest mark is 9 13/16 in.

More measuring tools

All measuring & woodworking calculators